{"product_id":"sonax-profiline-claydisc-150-lackknete-pad","title":"PROFILINE ClayDisc \"150\" clay pad","description":"\u003ch2\u003eMachine paint decon in a fraction of the time — SONAX PROFILINE ClayDisc \"150\"\u003c\/h2\u003e\n\n\u003cblockquote\u003e\n  \u003cp\u003e\u003cem\u003eWhat is a ClayDisc and how does it differ from a clay bar? This machine-driven clay pad from the PROFILINE line is built for random-orbital and DA polishers — it swaps hand-kneading for machine-speed decon, working the same area in a fraction of the time with more even cut.\u003c\/em\u003e\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\n\u003chr\u003e\n\n\u003cp\u003eEvery proper detail starts with decontamination: fallout, baked-on brake dust, industrial fallout and tree-sap contamination sit deep in the clearcoat and have to come off before you polish or seal. A classic clay bar does the job, but it eats time — on a mid-size car you're looking at 30–60 minutes by hand. The \u003cstrong\u003eSONAX PROFILINE ClayDisc \"150\"\u003c\/strong\u003e cuts that down hard: as a 150 mm dia. clay pad for dual-action random-orbital machines, the machine does the claying for you. Time per car drops to 10–15 minutes — and the whole panel gets treated more evenly than you'd manage by hand.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eMachine decon up to 5× faster than a hand clay bar.\u003c\/strong\u003e With the machine doing the work, the ClayDisc walks across the paint in broad, even passes — no missed spots, no patchy pressure. The DA's orbital throw creates a randomised claying motion that beats a straight-line hand stroke: the surface gets hit from several angles, which pulls off stubborn contamination that shrugs off a one-directional pass.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eWorks with DA random-orbital polishers on a standard hook-and-loop backing plate.\u003c\/strong\u003e The ClayDisc fits any orbital machine with a 150 mm dia. backing plate and Hook\u0026amp;Loop fastening — the standard format on most pro DA polishers. No adapter kit, no special machine. The clay is laid onto a carrier disc that takes the hook-and-loop directly and stays fully on the backing plate when you peel it — no delaminating, no clay layer lifting mid-job.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eReusable across plenty of cars — with the right care.\u003c\/strong\u003e The ClayDisc's clay picks up contamination and stores it in its surface. After each car, rinse the clay face with clean water and knead it (fold it in, squeeze it out) to work the trapped particles deeper and expose fresh surface. Look after it like that and one ClayDisc lasts several dozen cars before the face is fully saturated and needs replacing.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003chr\u003e\n\n\u003cblockquote class=\"praxistipp\"\u003e\n  \u003cp\u003e\u003cstrong\u003eDetailing1's tip from the shop:\u003c\/strong\u003e Always run plenty of lube with the ClayDisc — either a dedicated clay lubricant or, in a pinch, diluted car shampoo (2 ml to 500 ml water). Too little lube and the pad grabs and tears across the paint and can leave marring. Keep the machine at a low to medium speed (setting 2–3 on the DA) — more speed doesn't mean more decon, it just raises the risk of heat building up in the clay. After the ClayDisc pass, do a control wash or rinse with clean water before you prep the clearcoat for polish or sealant with \u003ca href=\"\/en\/products\/sonax-profiline-prepare-reiniger-kontrollspray-entfetter\"\u003eSONAX PROFILINE Prepare degreaser\u003c\/a\u003e.\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\n\u003chr\u003e\n\n\u003ch3\u003eClayDisc \"150\" clay technology — material, abrasion grade and decon performance\u003c\/h3\u003e\n\n\u003cp\u003eThe \u003cstrong\u003eSONAX PROFILINE ClayDisc \"150\"\u003c\/strong\u003e uses a thermoplastic polymer clay laid as a thin working layer on a firm carrier disc. That carrier disc handles the mechanical link to the machine (hook-and-loop) and spreads pressure evenly across the whole clay face. The clay itself sits in the mid-range of the clay-aggression scale — punchy enough to lift baked-on iron particles, fallout, sap and caked industrial dust, but gentle enough that the claying doesn't carve deep scratches into the clearcoat.\u003c\/p\u003e\n\n\u003cp\u003eThe aggression of a clay is a key parameter: too soft and it won't grab contamination effectively; too aggressive and it leaves marring in the clearcoat that you then have to polish out. The ClayDisc \"150\" sits in the medium to slightly aggressive band — plenty for most contamination on normal cars, without forcing a heavy correction pass afterwards just to clear marring. On very soft paint or fresh respray, do a test on a hidden spot, because any mechanical decon — even with lube — leaves minimal contact marks that can show up on very soft paint.\u003c\/p\u003e\n\n\u003cp\u003eThe DA's oscillating motion drives the clay across the surface from different angles and directions. That three-dimensional attack lifts contamination that sometimes holds firm under a one-directional hand stroke: the machine gets around the \"flow shadow\" that a directional claying motion can leave around firmly stuck particles. For very stubborn single spots — deep sap dots, say, or baked-in brake-dust deposits — a hand clay still wins on precision in those small areas, because you can build pressure more deliberately.\u003c\/p\u003e\n\n\u003cp\u003eOne core advantage of the machine over hand claying is consistent pressure: by hand, the pressure swings with fatigue and the angle of your wrist; with the machine, it stays constant across the whole working face. That gives you a more even decon result — treated the same everywhere, never overdone anywhere. On cars with big flat areas like bonnets and roofs the edge is measurable: the feel after the ClayDisc pass (that famous glass-smooth paint) is more even than after hand claying.\u003c\/p\u003e\n\n\u003cp\u003eThe ClayDisc's clay is formulated to resist solvents: in contact with clay lubricants that carry small amounts of cleaning agents, the clay keeps its structure and elasticity. That matters, because some detailers use quick detailers or dedicated lubes as lube, and these carry surfactants and polymers — which would soften a non-solvent-resistant clay and change its surface texture.\u003c\/p\u003e\n\n\u003ch3\u003eUsing the ClayDisc \"150\" — lube, machine speed and the run\u003c\/h3\u003e\n\n\u003cp\u003eThe right ClayDisc routine in the prep process: car fully washed and dried; then snap the ClayDisc onto the DA; spray the paint with plenty of lube (the panel should glisten wet, not drip); at setting 2–3, run even passes across the panel, keeping light pressure; overlap each pass 50% with the last; rinse the panel with clean water afterwards and dry it off.\u003c\/p\u003e\n\n\u003cp\u003eLube is the single most critical variable with the ClayDisc. Too little and the clay drags hard on the paint — you'll feel it as grabbing or juddering in the machine. The second you feel that resistance, drop the speed and add more lube. Too much lube and the clay \"floats\" and loses mechanical contact — decon performance drops off. You've got the right amount when the machine glides smoothly across the panel without skating. Good rule of thumb: about 5–8 sprays of clay lubricant on a 50×50 cm panel.\u003c\/p\u003e\n\n\u003cp\u003eFor stubborn local contamination (sap spots, say, or heavily brake-dusted areas behind the wheel arches) you can work the ClayDisc over that area with more pressure and several overlapping passes. Just don't tilt the machine — the ClayDisc has to sit flat on the surface so the whole clay face works evenly. A tilted disc only works on its edge, which both cuts effectiveness and raises the risk of edge marks. Take the machine up to setting 3, put direct pressure on the contaminated spot and make 3–4 passes — the clay works its way into the contamination and lifts it off layer by layer. After that more intense bit, always spray fresh lube and finish the whole panel back at normal setting 2.\u003c\/p\u003e\n\n\u003cp\u003eAfter the ClayDisc pass, rinse the disc under running water and knead and squeeze it hard to work the picked-up contamination deeper into the clay. Visibly dark or heavily discoloured spots on the clay face show where most of the contamination landed — those spots get kneaded in deeper next time round to expose fresh surface.\u003c\/p\u003e\n\n\u003ch3\u003eThe ClayDisc in the pro detailing process — workflow, time saved and quality control\u003c\/h3\u003e\n\n\u003cp\u003eIn a pro detailing shop the ClayDisc \"150\" is an efficiency tool that re-frames the whole decon step. Without it: 45–60 minutes of hand claying per car, hard going and tiring on the wrist. With the ClayDisc: 10–15 minutes of machine decon, a more even result, less physical strain on the detailer. At 5 cars a day the ClayDisc saves 2.5–3.5 hours of working time daily — time that's far better spent on other steps in the detail.\u003c\/p\u003e\n\n\u003cp\u003eQuality control after the ClayDisc pass is the touch test: run a freshly washed finger (in a protective glove) across the cleaned paint. A smooth, near-frictionless glide tells you the contamination is gone — the \"glass\" feel. Roughness and resistance as you glide mean there's contamination left, calling for either a second ClayDisc pass or a manual touch-up with the traditional \u003ca href=\"\/en\/products\/sonax-profiline-clay-knetmasse\"\u003eSONAX PROFILINE Clay bar\u003c\/a\u003e. The latter is often the more precise call for very small, stubborn spots — the ClayDisc for the open panels, the hand clay for the detail work.\n\n\u003c\/p\u003e\u003cp\u003eA common question in the shop: do you always have to polish after the ClayDisc? Technically no — claying on its own often leaves no visible marks, depending on clearcoat hardness and the lube you ran. Under strip lighting you'll see minimal contact patterns on very soft paint; on medium-hard to hard OEM clearcoat the paint is already very smooth and even after claying with no further work. If you're only sealing (no polish), a mild pass with a soft finishing pad and a light finishing polish is worth it to clear any clay marks and optimise the surface for the sealant to bond. Anyone polishing the car afterwards can often skip that intermediate step, since the polish removes the clay marks anyway.\u003c\/p\u003e\n\n\u003cp\u003eThe ClayDisc \"150\" is built primarily for the prep step before polishing. After a successful decon pass the paint is free of contamination, but the claying has left the finest surface marks — comparable to very fine scratches from a mild abrasive. Those marks come fully out in the following polishing step (even with a medium-hard foam pad and a mild polish), so the finished result after the full detail shows no clay marks at all. Seal straight after the ClayDisc without polishing and you risk locking those marks in under the sealant.\u003c\/p\u003e\n\n\u003ch3\u003eClayDisc \"150\" compared — clay disc vs. hand clay bar vs. chemical decon\u003c\/h3\u003e\n\n\u003cp\u003eThe classic \u003ca href=\"\/en\/products\/sonax-profiline-clay-knetmasse\"\u003eSONAX PROFILINE Clay bar\u003c\/a\u003e is the proven tool for hand decon — it lets you do precise detail work on edges, mirrors and small areas, but it eats time on big panels. The ClayDisc \"150\" is its counterpart for machine work on open areas: large-area, fast, even. In pro detailing the two tools sensibly work together: ClayDisc for the bonnet, roof, wings and doors; hand clay for bumper edges, the undersides of spoilers and spots the big disc can't reach well.\u003c\/p\u003e\n\n\u003cp\u003eThe alternative to mechanical decon is chemical iron removers and clay substitutes (clay towels, clay mitts). Chemical iron removers like the SONAX PROFILINE fallout remover dissolve metallic iron particles chemically — they're especially good on brake-dust iron particles, but they can't remove every type of contamination (sap, industrial fallout). Clay towels and clay mitts work much like the ClayDisc but are softer and better suited to delicate paint. The ClayDisc \"150\" pairs the abilities of a clay with the speed of the machine, which makes it the most efficient all-round tool for full-panel mechanical decon in a pro setup.\u003c\/p\u003e\n\n\u003ch3\u003eBuying the SONAX PROFILINE ClayDisc \"150\" — planning, care and reuse\u003c\/h3\u003e\n\n\u003cp\u003eFor pro detailing shops decontaminating several cars a day, the ClayDisc \"150\" is a soundly economical investment: a well-cared-for ClayDisc lasts 30–50 cars or more, depending on how heavy the contamination is. By comparison, a hand clay typically drops off noticeably in cleaning power after 8–12 cars. The higher up-front price of the ClayDisc against a hand clay pays for itself quickly through the longer service life and the saved working time.\u003c\/p\u003e\n\n\u003cp\u003eTelltale signs of a spent ClayDisc: the clay face is dark all over (fully saturated with contamination), has no elasticity left, or shows cracks and lifting spots. A spent ClayDisc won't decontaminate effectively anymore, even rinsed with water — the clay has no capacity left to take on new contamination. In that state, replace it, since working on with a saturated disc gets you no cleaning power at all.\u003c\/p\u003e\n\n\u003cp\u003eBetween cars, always store the ClayDisc damp — drying out turns the clay hard and brittle. If a dried-out clay face is wetted again, it takes several minutes for the elasticity to come back — and during that window working with the disc isn't advisable, since hard clay marks the paint rather than lifting contamination. Taking a break? Drop the ClayDisc straight into water. Easy method: lay the ClayDisc in a shallow plastic tray with a bit of water and keep it covered between uses. After the working day, store the ClayDisc cool in a damp, covered container. As a verified SONAX dealer, Detailing1 keeps the PROFILINE ClayDisc \"150\" in the range permanently. To get the most life out of the disc, it's worth running a chemical iron remover before the machine claying: it dissolves the iron-rich contamination chemically first, so the ClayDisc has less mechanical work to do and its clay face stays fresh longer.\u003c\/p\u003e","brand":"SONAX","offers":[{"title":"1 piece \/ Ø 150 mm","offer_id":57345154941263,"sku":"D1-SNX-4512410","price":40.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0800\/3272\/7375\/files\/sonax-profiline-claydisc-150_1-stueck.png?v=1774736525","url":"https:\/\/detailing1depot.com\/en\/products\/sonax-profiline-claydisc-150-lackknete-pad","provider":"Detailing1","version":"1.0","type":"link"}