{"product_id":"sonax-profiline-ex-05-05-schleif-politur-heavy-cut","title":"PROFILINE EX \"05-05\" Cutting Compound (Heavy-Cut)","description":"\u003ch2\u003eRemove deep scratches on the dual-action polisher with the SONAX EX 05-05 cutting compound\u003c\/h2\u003e\n\n\u003cblockquote\u003e\n  \u003cp\u003e\u003cem\u003eWhat can the SONAX EX 05-05 do? A heavy-cut cutting compound for dual-action polishers with a cut rating of 5\/5 and a gloss rating of 5\/5 — it removes deep scratches, sanding marks up to P1500 and heavy weathering, and with the HybridwollPad it gets you results on a rotary level.\u003c\/em\u003e\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\n\u003chr\u003e\n\n\u003cp\u003eFor a long time, dual-action polishers were seen as the safe but weak tool — fine for finishing work, but no good for serious defect correction. Deep scratches, sanding marks and heavy weathering were the domain of the rotary, because only it built enough friction energy for the material removal you need. The \u003cstrong\u003eSONAX EX 05-05\u003c\/strong\u003e breaks with that limitation. Paired with a HybridwollPad, this cutting compound gets you results on the dual-action that used to be reserved for the rotary: sanding marks up to P1500 disappear in a single pass, deep scratches and etching are pulled out reliably, and the 5\/5 gloss rating leaves a finish that often needs no extra polishing step. For detailers who want to — or have to — work the dual-action only, because the rotary is too risky on certain paints, the EX 05-05 is the cutting compound of choice.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eHeavy-cut on the dual-action.\u003c\/strong\u003e With a cut rating of 5\/5, the EX 05-05 is the most aggressive polish in the SONAX EX line-up. Its abrasive blend is built so it still generates enough cut even at the lower friction energy of dual-action motion, enough to remove deep scratches and sanding marks up to P1500. Paired with the HybridwollPad — a pad that combines foam and lambswool fibres — cutting power climbs noticeably again, because the wool fibres add friction that pure foam pads simply can't deliver.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eHigh gloss at the same time.\u003c\/strong\u003e The 5\/5 gloss rating shows the EX 05-05 doesn't just cut, it polishes too. The abrasives break down progressively over the polishing pass — from coarse to fine — and leave a surface that on many paints is already the end result you wanted. When the finish demands the very best, a short pass with the \u003ca href=\"https:\/\/detailing1.de\/products\/sonax-profiline-ex-04-06-hochglanz-politur\"\u003eEX 04-06\u003c\/a\u003e follows, but for everyday needs the EX 05-05 often does the job as a one-step solution.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSilicone-free and low-dust.\u003c\/strong\u003e The formula is free of silicones and, thanks to its optimised consistency, works almost dust-free. In paint shops the silicone-free build eliminates the contamination risk, and the low-dust working saves time on the clean-up. Especially with heavy defect correction that takes several passes and a lot of polishing work, the low-dust formula makes a real difference in comfort and in how clean your work area stays.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003chr\u003e\n\n\u003cblockquote class=\"praxistipp\"\u003e\n  \u003cp\u003e\u003cstrong\u003eDetailing1's tip from the shop:\u003c\/strong\u003e For maximum cut on the dual-action, pair the EX 05-05 with the SONAX HybridwollPad and work at speed 5 to 6 (depending on the machine). Apply moderate pressure and guide the machine across the surface at two to three centimetres per second — clearly slower than when you're finish-polishing. The trick: let the machine do the work and use the weight of the tool as your natural down-pressure. Don't force the machine into the surface — that stalls the dual-action motion and reduces the cut instead of raising it.\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\n\u003chr\u003e\n\n\u003ch3\u003eCutting compound for the dual-action — how the EX 05-05 gets rotary results on a DA\u003c\/h3\u003e\n\n\u003cp\u003eThe key to the performance of the \u003cstrong\u003eSONAX EX 05-05\u003c\/strong\u003e lies in the match between abrasive and pad. The abrasive particles are sized to work best at the specific friction energy of a dual-action polisher: big enough for effective cut, small enough for controlled particle break-down. On a rotary these particles would break too fast and lose their cutting power — so the EX 05-05 isn't a universal polish, it's a specialist for the dual-action motion.\u003c\/p\u003e\n\n\u003cp\u003eThe HybridwollPad amplifies this effect: the lambswool fibres create extra micro-friction on the surface that boosts material removal, while the foam core keeps the heat in check. The result: a cut on the dual-action that gets close to the level of a rotary with a medium-hard foam pad — without the rotary's risks (holograms, hot spots, burning through on edges).\u003c\/p\u003e\n\n\u003cp\u003eThe EX 05-05 plus HybridwollPad combo does have its limits, though: sanding marks of P1000 and coarser can't be fully removed in a single pass on the dual-action, even with this aggressive pairing. Here the rotary with a polish like the \u003ca href=\"https:\/\/detailing1.de\/products\/sonax-profiline-cutmax-schleif-politur\"\u003eCutMax\u003c\/a\u003e stays on top. The EX 05-05 covers the range from P1500 down to light P1200 marks — and in that range it gives you a result on the dual-action that makes switching to the rotary unnecessary.\u003c\/p\u003e\n\n\u003cp\u003eFor anyone who rarely uses their dual-action for heavy-cut, an important note: the performance of the EX 05-05 depends a lot on the quality of the dual-action. Cheap entry-level DAs with a short throw (8 mm) and a weak motor hit their limits fast on heavy defects. Machines with a long throw (15 to 21 mm) like the common pro models deliver far more friction energy and tap the EX 05-05's potential better. If you're planning to do heavy-cut work on the dual-action regularly, the investment in a long-throw machine pays off.\u003c\/p\u003e\n\n\u003ch3\u003eUsing the EX 05-05 the right way — pad choice, speed and technique\u003c\/h3\u003e\n\n\u003cp\u003eThe \u003cstrong\u003eEX 05-05\u003c\/strong\u003e shows its full strength paired with the HybridwollPad. For less aggressive jobs — say on near-new paint with only light scratches — a hard foam pad (orange) works too, giving slightly less cut at slightly higher gloss. On a soft finishing pad the compound loses too much cutting power — for pure finish-polishing the \u003ca href=\"https:\/\/detailing1.de\/products\/sonax-profiline-ex-04-06-hochglanz-politur\"\u003eEX 04-06\u003c\/a\u003e is the better call.\u003c\/p\u003e\n\n\u003cp\u003ePut three to four pea-sized dots on the pad and spread the compound over the panel at a low speed. Step up to speed 5 to 6 and work in slow, overlapping passes across the section. A typical section — about half a fender — takes three to four minutes on the dual-action. By the end of the pass the compound should sit clear and thin on the surface — the sign that the abrasives have fully broken down.\u003c\/p\u003e\n\n\u003cp\u003eThe \u003cstrong\u003emachine handling\u003c\/strong\u003e on the EX 05-05 differs from a finishing polish: with heavy-cut you can apply a bit more pressure than when finish-polishing, but only ever enough that the dual-action motion doesn't come to a stop. The moment you feel the machine stalling or vibrating, take the pressure off straight away. A stalling pad creates localised heat that can cause thermal damage on sensitive paints — showing up as light discolouration or dullness that even re-polishing can no longer fully correct.\u003c\/p\u003e\n\n\u003cp\u003eWhen you work on \u003cstrong\u003eedges and raised lines\u003c\/strong\u003e, take extra care: the clearcoat there is often only half as thick as on the flats. Drop the pressure clearly in these areas and rather run one extra pass with little pressure than a single pass with too much cut. A coating thickness gauge before you start gives you certainty about the room you've got to work with.\u003c\/p\u003e\n\n\u003cp\u003eAfter the pass, wipe the residue off with a clean microfibre cloth and check under LED light. If defects are still visible, repeat the pass on the same section. With the EX 05-05, two to three passes per panel on hard European paints are nothing unusual — on softer Japanese or Korean paints a single pass is often enough. Match your expectations to the paint type and plan in enough time, instead of giving up after one pass when the result isn't right yet.\u003c\/p\u003e\n\n\u003cp\u003eDegrease the polished surface afterwards with \u003ca href=\"https:\/\/detailing1.de\/products\/sonax-profiline-prepare-reiniger-kontrollspray-entfetter\"\u003eSONAX PROFILINE Prepare\u003c\/a\u003e to see the true result. Polishing oils can visually mask leftover defects — under Prepare it becomes clear whether all the scratches have really gone or whether another pass is needed.\u003c\/p\u003e\n\n\u003ch3\u003eHeavy-cut on the dual-action — typical use cases\u003c\/h3\u003e\n\n\u003cp\u003eThe main field for the \u003cstrong\u003eSONAX EX 05-05\u003c\/strong\u003e is defect correction on paints that are too sensitive for the rotary, or where you prefer the safety of the dual-action. Day-to-day, that comes down to a few scenarios:\u003c\/p\u003e\n\n\u003cp\u003eWhen you're \u003cstrong\u003edetailing dark paints\u003c\/strong\u003e (black, dark blue, dark grey), the dual-action is the safer call, because it throws fewer holograms than the rotary. On these demanding colours the EX 05-05 delivers enough cut to remove scratches and swirls, and the 5\/5 gloss rating keeps the rework to a minimum. On black paint a short finishing pass with the EX 04-06 often makes sense, to pull out that last bit of deep gloss.\u003c\/p\u003e\n\n\u003cp\u003eOn \u003cstrong\u003ecars with a thin clearcoat layer\u003c\/strong\u003e — measured with a coating thickness gauge — the dual-action gives you more control over material removal. The EX 05-05 removes defects efficiently, but more controlled than a rotary polish, because the dual-action motion takes off less per unit of time. That gives you the chance to check progress after every pass and stop in time, before the clearcoat gets too thin.\u003c\/p\u003e\n\n\u003cp\u003eFor \u003cstrong\u003escratch removal in hard-to-reach spots\u003c\/strong\u003e — door-handle recesses, swage lines, transitions between panels — the compact dual-action with a small pad (75 mm or 125 mm) is a better fit than the big rotary. The EX 05-05 works on all common pad sizes and adapts flexibly to the panel geometry.\u003c\/p\u003e\n\n\u003cp\u003eOne more scenario that pro detailers value: \u003cstrong\u003ecorrecting transport damage and car-wash scratches\u003c\/strong\u003e on new vehicles. Plenty of new cars arrive at the dealer with fine to medium scratches — caused by film removal, transport securing or careless cleaning out on the lot. The EX 05-05 removes these defects on the safe dual-action, without putting the thin factory paint at risk. Combined with a final ceramic coating, the car ends up better protected than it was in delivery condition.\u003c\/p\u003e\n\n\u003ch3\u003eCutting compound comparison — EX 05-05 vs. CutMax vs. Cut+Finish\u003c\/h3\u003e\n\n\u003cp\u003eThe three key cutting compounds in the SONAX PROFILINE range cover different machine types and demands:\u003c\/p\u003e\n\n\u003cp\u003eThe \u003cstrong\u003e\u003ca href=\"https:\/\/detailing1.de\/products\/sonax-profiline-cutmax-schleif-politur\"\u003eCutMax (6\/4)\u003c\/a\u003e\u003c\/strong\u003e is the cutting compound for the rotary — maximum cut (6\/5), moderate gloss (4\/5), optimised for the high friction energy of the rotary. It's the first choice for heavy defects from P1000 up on the rotary.\u003c\/p\u003e\n\n\u003cp\u003eThe \u003cstrong\u003e\u003ca href=\"https:\/\/detailing1.de\/products\/sonax-profiline-cut-finish-einstufen-politur\"\u003eCut+Finish (5\/5)\u003c\/a\u003e\u003c\/strong\u003e is the one-step solution for the rotary — same cut value as the EX 05-05, but with a high-gloss finish at the same time. It covers the range from P1500 up and combines cutting and finishing in a single pass.\u003c\/p\u003e\n\n\u003cp\u003eThe \u003cstrong\u003eEX 05-05 (5\/5)\u003c\/strong\u003e is the counterpart to the Cut+Finish for the dual-action: same performance values, but a formula optimised for the kinematics of the DA. If you own a dual-action and want to do heavy defect correction, you reach for the EX 05-05. If you've got a rotary, you take the Cut+Finish or CutMax. A universal polish that works equally well on both machine types doesn't exist — the physical demands of the two motions are too different. That's why SONAX deliberately developed separate product lines for rotary and dual-action with the PROFILINE range, rather than offering compromise products that don't show their full strength on either machine.\u003c\/p\u003e\n\n\u003ch3\u003eBuying the EX 05-05 — sizes and recommendation\u003c\/h3\u003e\n\n\u003cp\u003eThe \u003cstrong\u003eSONAX EX 05-05\u003c\/strong\u003e comes in 250 ml and 1000 ml. For the occasional job detailing your own car, the 250 ml bottle is enough — a full defect correction uses between 50 and 100 ml depending on the size of the car and how bad the defects are. The 1000 ml bottle is the more economical option for detailing businesses and keen enthusiasts.\u003c\/p\u003e\n\n\u003cp\u003eIn the optimal workflow for the dual-action, the EX 05-05 is the first step (heavy-cut), followed by the EX 04-06 as the finishing step and \u003ca href=\"https:\/\/detailing1.de\/products\/sonax-profiline-prepare-reiniger-kontrollspray-entfetter\"\u003eSONAX Prepare\u003c\/a\u003e for degreasing and checking the result. This two-step process on the dual-action gets you results that come close to a three-step process on the rotary — at clearly lower risk of holograms and burn-through.\u003c\/p\u003e\n\n\u003cp\u003eAnyone with both EX-series polishes on the shelf — the EX 05-05 for heavy-cut and the EX 04-06 for finish — is set up for every dual-action job. The two products complement each other perfectly: the EX 05-05 removes the heavy defects, the EX 04-06 pulls out the last bit of gloss. Together they replace a three-product system (cutting paste, cutting compound, finishing polish) of the kind that's standard with the rotary — fewer products, fewer pad changes, fewer things to get wrong.\u003c\/p\u003e\n\n\u003cp\u003eFor economical use: the product consumption of the EX 05-05 on heavy-cut work runs a bit higher than on a finishing polish, because you need more passes per panel. For a full defect correction on the dual-action, count on around 80 to 120 ml per car — depending on the size of the car and how bad the defects are. The 250 ml bottle does two to three cars that way, the 1000 ml bottle eight to twelve.\u003c\/p\u003e\n\n\u003cp\u003eOne tip for pad care: the HybridwollPad should be cleaned thoroughly after every car — polish residue in the wool fibres hardens and reduces cutting power on the next job. Rinse the pad out under warm water after the work and let it dry fully before you use it again. You can tell a worn-out HybridwollPad by the wool fibres being flattened and no longer springing back — that's when it's time for a new pad. Rather invest in a fresh pad than in an extra polishing pass: the cut of a new pad is noticeably higher than that of a worn one, and the result more even. Professional outfits change the HybridwollPad after five to eight cars at the latest — beyond that the wool structure is so compacted that the cut drops off noticeably and you're no longer getting the full efficiency out of the EX 05-05.\u003c\/p\u003e\n","brand":"SONAX","offers":[{"title":"250ml","offer_id":53520446619983,"sku":"D1-SNX-2451410","price":24.0,"currency_code":"USD","in_stock":true},{"title":"1000 ml \/ 1 liter","offer_id":53520446652751,"sku":"D1-SNX-2453000","price":53.0,"currency_code":"USD","in_stock":true},{"title":"2x 250ml set","offer_id":53520446685519,"sku":"D1-SNX-2451410_2","price":47.0,"currency_code":"USD","in_stock":true},{"title":"3x 250ml set","offer_id":53520446718287,"sku":"D1-SNX-2451410_3","price":70.0,"currency_code":"USD","in_stock":true},{"title":"2x 1 Liter Set","offer_id":53520446751055,"sku":"D1-SNX-2453000_2","price":105.0,"currency_code":"USD","in_stock":true},{"title":"3 x 1 Liter Set","offer_id":53520446783823,"sku":"D1-SNX-2453000_3","price":158.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0800\/3272\/7375\/files\/sonax-profiline-ex-05-05-schleif-politur-heavy-cut.png?v=1730649133","url":"https:\/\/detailing1depot.com\/en\/products\/sonax-profiline-ex-05-05-schleif-politur-heavy-cut","provider":"Detailing1","version":"1.0","type":"link"}