SONAX PROFILINE SP "06-02" Cutting Polish (Heavy-Cut) 250ml

Remove deep scratches, sanding marks and overspray with SONAX PROFILINE SP "06-02"

What can the SP "06-02" from SONAX PROFILINE do? This silicone-free heavy-cut compound with cut level 6 removes sanding marks up to P1200, overspray, etching damage and deeply embedded scratches on all paints — as the first step in a professional polishing workflow.

In professional paint correction there's no "one-does-it-all" polish. A solid multi-step workflow splits the job: first a heavy-cut compound grinds out the coarse defects, then a finishing polish refines the result until the paint sits there free of marring and with maximum gloss. That role as the first and most powerful step is exactly what the SONAX PROFILINE SP 06-02 takes on — a silicone-free cutting compound with cut level 6, built for work with the rotary polisher. It removes sanding marks from wet-sanding up to P1200, overspray, etching damage from bird droppings, insects and tree sap, plus badly weathered single-stage paints. SONAX PROFILINE's SP polish system is firmly established in professional paint correction: the clearly defined cut and gloss levels let you plan a multi-stage workflow precisely, where every polish handles exactly what it was built for — and the SP "06-02" is the strongest, most abrasive tool in the whole set. It stands for the first, decisive step, without which the refinement steps that follow couldn't do their job.

• Cut level 6 for defects other polishes can't touch. Deeply embedded scratches, sanding marks after wet-sanding with P1000 or P1200, baked-on overspray and heavily oxidised paint surfaces: those are the jobs the SP "06-02" was designed for. Conventional medium-cut polishes at cut level 4 or 5 fall short here — the SP "06-02" clears them systematically and under control, without stripping away more clear coat than it needs to.
• Silicone-free — fit for rework and respray jobs. Silicone-based polishes leave behind residues that are hard to remove and can cause fisheyes and adhesion problems on later respray or sealing work. The SP "06-02" is formulated completely silicone-free — it leaves no traces that get in the way of later paint correction, which makes it the standard for professional shops and bodyshops that also respray.
• Defined finish for predictable follow-up polishing. The SP "06-02" leaves a defined, even finish on the paint that the follow-up polish PROFILINE FS 05-04 can refine in a targeted, efficient way. The matched cut and gloss levels in the PROFILINE system are no accident — they let you run a workflow where the next step always builds on the last, with no needless in-between passes or do-overs.

Day-to-day from Detailing1: always work the SP "06-02" on clean, dust-free paint and degrease the surface beforehand with an IPA mix (isopropyl alcohol) to pull off residues from waxes or care products. On the first pass, use higher pressure (5–10 kg) at lower speed (800 RPM) to activate the abrasive and cut down the defect. Then drop the pressure and raise the speed (1200 RPM) for the refining phase. Always work in a crosshatch pattern to avoid transitions. After the SP "06-02", always check the defined finish under good lighting before moving on to the FS 05-04.

Cut level 6 and gloss level 2 — how the SP "06-02" works through paint defects

The SONAX PROFILINE system defines cut and gloss levels on a scale that makes picking the right polish for each defect level easy. Cut level 6 is the highest cut in the SP range — it's an aggressive cut that reaches even stubborn defects like deeply embedded scratches and wet-sanding marks up to P1200. At the same time, gloss level 2 means the SP "06-02" leaves a certain haze after polishing that a finishing polish has to refine further. That's not a drawback, it's the plan: a heavy-cut compound that also delivers maximum gloss always compromises either the cutting power or the finish. The SP "06-02" is optimised for the first step — and it does that step so well that the second step with the FS 05-04 becomes efficient and predictable.

The abrasive formulation of the SONAX PROFILINE SP 06-02 works with mineral abrasives that turn actively abrasive under the pressure of the rotary polisher. These so-called "breaking down" abrasives break apart as the polishing goes on: on the first pass at high pressure they hit with their full aggression, on the second pass at reduced pressure they get finer and produce a more even finish. This self-breaking behaviour is why the SP "06-02", despite its cut level 6, gives a controlled and predictable result — the paint isn't removed at random, it's worked systematically. If you want to understand why professional detailers rate the PROFILINE system, here's one of the core reasons: the chemistry works with the machine, not against it.

Important for practice: the SP "06-02" is built for work with the rotary polisher, not for dual-action machines. Rotary machines generate the heat and pressure you need to activate the abrasives properly. With a dual-action machine at low cut and moderate pressure you can in theory use a heavy-cut compound, but the result and the efficiency are clearly worse. In the pro use the SP "06-02" is designed for, only the rotary machine comes into play — ideally with a wool pad for maximum cut, or a hard foam pad for a controlled finish on more delicate paints.

Using the SP "06-02" the right way — the rotary-polisher workflow

Phase 1 starts with a prepped paint area, cleared of dust and dirt. The panel you're working should also be at room temperature — cold paint reacts to the abrasives differently than warm, and below 10 °C the polish can't reach its full effect. Put product on the pad — not too much, about 4–6 pea-sized drops for an area of roughly one square metre. Then start at 5–10 kg pressure at 800 RPM and move evenly across the area you're working. The higher pressure activates the abrasives and makes sure the defects come out efficiently. This phase takes about 30 seconds per square metre and is the actual cutting step.

Phase 2 follows straight after: drop the pressure to 1–2 kg, raise the speed to 1200 RPM. Now the SP "06-02" switches into the refining phase. The abrasives, now finer, level the surface created in phase 1 and produce the even, defined finish that's the ideal starting point for the follow-up FS polish. This phase takes about 60 seconds per square metre. Then lift the residue with a clean microfibre cloth and check the result under good lighting — ideally with an LED inspection lamp. If defects are still showing, repeat the phase before you lay on the next polish. The crosshatch pattern matters here: even overlaps of 50 % of the pad face prevent transitions and uneven cutting depths.

A practical note on pad choice: the SONAX PROFILINE wool pad delivers the highest cut with the SP "06-02" and is first choice on hard-to-reach defects or large-area weathering damage. The hard foam pad offers a bit less aggression but a more even finish and less heat build-up — ideal on more delicate paints or when you want tighter control over the cut. So the call between the pads comes down to the paint's condition and the job: the more aggressive the defects, the more it's wool; the more delicate the paint, the more it's the hard foam pad. If you've got both pads in the set, you can switch from wool to the foam pad after the first round to harmonise the finish further before the FS 05-04 — that often saves a separate polishing pass.

After the SP "06-02" the paint is in a state that still shows holograms and fine sanding marks under direct light — that's intended and expected. The follow-up polish's job is exactly that: to refine this defined finish further, until the paint sits there hologram-free and high-gloss. Using the SP "06-02" as your only polish and laying a wax over it wouldn't get you anywhere — it's the first step, not the last.

Where it fits — when the SP "06-02" is the right call

The SP "06-02" bites in situations where medium-cut polishes no longer cut it: freshly resprayed panels with orange-peel or sanding-grit marks, cars with deep swirl marks after years without professional correction, heavily weathered single-stage paints on classic cars, and above all follow-up work after wet-sanding with P1000–P1200. In damage repair — after hail damage with small sanding spots, after bird-dropping etches that have gone deep into the clear coat — the SP "06-02" is the tool of choice, because the medium polishes don't fully reach the depth of that damage. In overspray removal too, where you need the abrasive action to sand off the deposited foreign-paint particles, the SP "06-02" shows its full strength.

The SP "06-02" has its limits on extremely thin or already heavily thinned paints. On cars that have already been professionally corrected several times and whose clear coat has little thickness left, you should measure the paint thickness before reaching for a heavy-cut product. That's no failing of the SP "06-02" — it's a general principle of any abrasive work that gets factored in automatically in pro use. Used correctly, the SP "06-02" removes defined and controllable amounts of clear coat and isn't a tool for the occasional user with no rotary experience. Professional detailers generally recommend always working a test area in a less visible spot before the first pass on an unknown car, to get a feel for the paint hardness and the cut — every paint reacts a little differently, and what works fine on a soft Japanese clear coat needs clearly more machine pressure and dwell time on a hard German clear coat.

The SP "06-02" in the polish system — the three-step PROFILINE workflow

The SONAX PROFILINE polish system is designed as a matched three-step system. Step one: the SP "06-02" as a heavy-cut compound removes the coarse defects and creates the defined finish. Step two: the PROFILINE FS 05-04 — a medium-cut finishing polish with cut level 5 and gloss level 4 — refines the SP "06-02" result and clears the holograms and sanding marks left in the first step. Step three: the PROFILINE NP 03-06 brings the final high gloss with cut level 3 and gloss level 6 and leaves the paint in a mark-free state, ready for every sealant and protective product. This grading from 6 through 5 and 4 to 3 and 6 is no accident — it mirrors a carefully developed progression that does exactly what the next step needs at every stage.

If you've got fewer defects and want to get by with a single polish, you can reach for the PROFILINE UltimateCut — a high-speed cutting polish built for one-step use on dual-action and rotary machines. The UltimateCut is aggressive and efficient, but not as strongly cutting as the SP "06-02", and it delivers a better finish at the same time — a trade-off that makes sense for a lot of everyday jobs. If instead you need maximum cut with a clearly defined follow-up workflow — and that's the typical demand in professional paint correction — you're best set up with the SP "06-02" in a full three-step system.

Buying advice — who the SONAX PROFILINE SP 06-02 pays off for

The SP "06-02" is the right tool for professional detailers, painters and keen enthusiasts who work with the rotary polisher and want to tackle demanding paint defects systematically. It pays off whenever medium polishes no longer cut it: after wet-sanding, on deep scratches, on overspray or on heavily weathered paints. If you're after a single heavy-cut solution for pro use, you'll find the SP "06-02" a reliable, easy-to-run product from a matched system. Together with the FS 05-04 and NP 03-06 you get a complete, scalable correction workflow that suits practically any task in professional paint polishing — from simple scratch removal to full paint restoration. The 250 ml bottle suits getting started and trying the system out, the 1 L container the daily pro use. Deciding on the SP 06-02 also means deciding on a clear way of working: not fast and with cut corners, but systematic and with a result. For keen hobby detailers working their way into professional paint correction, the SP system is an excellent way in — the clear levels and the predictable behaviour make it easier to understand and fine-tune your own approach. For pros correcting cars every day, the SP "06-02" is a reliable constant in the workflow you can lean on without surprises. And for bodyshops that offer correction work alongside repairs, it's the right tool to tackle even the most stubborn paint damage systematically and with a reproducible result.